Otasuke Pro! > FAQ > GP3000 > Connection devices that the Ladder Monitor is available with and versions of the programming tools

FAQ

Connection devices that the Ladder Monitor is available with and versions of the programming tools

Supporting models

■ Mitsubishi Electric

■ OMRON

Maker	Series	CPU	Link Interface or CPU Direct	Communication Method *1	Device Name for GP-Pro EX *2
OMRON Corporation	CS1 Series	CS1H-CPU67 CS1H-CPU66 CS1H-CPU65 CS1H-CPU64 CS1G-CPU45 CS1G-CPU44 CS1G-CPU43 CS1G-CPU42 CS1H-CPU67H CS1H-CPU66H CS1H-CPU65H CS1H-CPU64H CS1H-CPU63H CS1G-CPU45H CS1G-CPU44H CS1G-CPU43H CS1G-CPU42H CS1H-CPU67-V1 CS1H-CPU66-V1 CS1H-CPU65-V1 CS1H-CPU64-V1 CS1H-CPU63-V1 CS1G-CPU45-V1 CS1G-CPU44-V1 CS1G-CPU43-V1 CS1G-CPU42-V1	RS-232C port on CPU unit	RS232C or RS422/485 (4 wire)	CS/CJ Series HOST Link (Ver.1.13.02 or later)
			Peripheral port on CPU unit
				Ethernet	CS/CJ Series Ethernet (Ver.1.14.03 or later)
			CS1W-SCU21 CS1W-SCU21-V1 CS1W-SCB21 CS1W-SCB41
			CS1W-ETN01 CS1W-ETN11 CS1W-ETN21 *3
	CJ1 Series	CJ1G-CPU45 CJ1G-CPU44 CJ1M-CPU23 CJ1M-CPU22 CJ1M-CPU21 CJ1M-CPU13 CJ1M-CPU12 CJ1M-CPU11 CJ1H-CPU67H CJ1H-CPU66H CJ1H-CPU65H CJ1H-CPU67H-R CJ1H-CPU66H-R CJ1H-CPU65H-R CJ1H-CPU64H-R CJ1G-CPU45H CJ1G-CPU44H CJ1G-CPU43H CJ1G-CPU42H	RS-232C port on CPU unit	RS232C or RS422/485 (4 wire)	CS/CJ Series HOST Link (Ver.1.13.02 or later)
			Peripheral port on CPU unit		CS/CJ Series Ethernet (Ver.1.14.03 or later)
			CJ1W-SCU41 CJ1W-SCU41 CJ1W-SCU21 CJ1W-SCU41-V1 CJ1W-SCU31-V1 CJ1W-SCU21-V1
			CS1W-ETN01 CS1W-ETN11 CS1W-ETN21 *3	Ethernet
	CP1 Series	CP1L-M□□D□-□ CP1L-L□□D□-□	CP1W-CIF01	RS232C	CS/CJ Series HOST Link (Ver.1.13.02 or later)
			CP1W-CIF11	RS422/485 (4 wire)
		CP1H-X□□D□-□ CP1H-XA□□D□-□ CP1H-Y□□D□-□	CP1W-CIF01	RS232C or RS422/485 (4 wire)	CS/CJ Series Ethernet (Ver.1.14.03 or later)
			CP1W-CIF11
			CJ1W-SCU41 CJ1W-SCU21 CJ1W-SCU41-V1 CJ1W-SCU31-V1 CJ1W-SCU21-V1
			CJ1W-ETN21 *3	Ethernet

OMRON Programming Tool

CX-Programmer Series Ver.7 or lower

IMPORTANT

If the driver version of the connected device, that is installed in GP-Pro EX is older than that listed in the table above, the ladder monitor will not function normally.
Upgrade the driver to at least the version listed in the table before using the unit.
The update module can be downloaded from our website "Otasuke Pro!"
> PLC Drivers

NOTE

-	This information is as of November 2008.
-	Instructions that can be monitored using this function are those supported by the CX-Programmer Series Ver.7 programming tool or lower by OMRON Corporation.
*1	The communication method changes depending on the type of the link unit, cables used, etc. For the details, see the driver manual.
*2	The driver version can be checked by viewing [Peripheral List] in the System Settings window of GP-Pro EX, or [Driver Version] in the Offline mode on the display unit.
*3	Compatible with both Ethernet transfer protocols, UDP/IP, and TCP/IP.

↑Back to page top

← Return to the previous page