>PLCs >Digital Electronics Corporation General Ethernet Driver
Please acknowledge the following terms of use before you use our download service. Download of any file signifies your agreement to the terms of use.
Terms of Use
Schneider Electric Japan Holdings Ltd. ("SEJH") shall retain all intellectual property rights to the files that SEJH provides for this service.
Who, uses or plans to use SEJH's products, may download and use any file.
Reproduction, disclosure, re-publication, assignment, lease, decompilation, modification, falsification or reuse of any file that SEJH provides for this service shall be prohibited.
However, for manuals, samples, BMP images and CAD files, you may reprint, duplicate, quote a part of the content or the whole on your company's specification sheets, or instruction manuals for built-in products. Also you may change the layout of the content.
This download service is provided through the Internet. Please acknowledge that SEJH provides no guarantee of the condition at the time of provision, the availability of access and the condition of use concerning this service before you use this service.
Please use this service at your own risk.
If any additional conditions such as service usage conditions are attached to the downloaded files, please comply with such conditions as well.
Notices:
Files are subject to deletion, or modification of the contents or specifications without notice.
Please confirm that the downloading file size completely accords
with the download file size shown.
If the file sizes do not match, delete the file without decompressing and then download the same file once again.
For details, please read the following
PDF:dig_gene.pdf ( 541KB )
For general information regarding Device connection and documentation conventions, please refer to "Device/PLC Connection Manual".
Updated Contents
Ver. 1.11.02 (Nov. 12, 2009)
The following issues were corrected:
The source port number destination cannot be switched between the Memory table and U/I destinations in some cases.
CPU utilization may become 100% when the driver is used with WinGP.
In the offline mode, different numbers can be set as the local Port No. in the Communication Settings and the Control Area 1 settings.
A number smaller than 1024 can be set as the local port number in the offline mode of Middle-size display units.
GP-Pro EX may look as if it were locked up when an out-of-range value is input in the Control Area Setting dialog.
An error occurs when a command is sent with the Attribute Bit2, Bit3, and Bit4 ON.
Opening the connection may lead to an error when the port number auto-allocation setting is enabled.
A warning dialog may be displayed twice when an out-of-range value is input in the Control Area Setting dialog.
Installation (This file is self-extracting.)
Please confirm that the supported software is installed in your computer. Prior to installing the driver, close all your personal computer applications, including any resident programs such as virus detection program, etc.
Click on the above file name to download the data to desired folder.
After the download to your PC is finished, double-click on the file’s icon to start the installer program.
After the installer starts, follow the instructions given on each screen.
After installation, execute GP-Pro EX.
After installation, click on the Device/PLC area’s [Digital Electronics Corporation.] selection and select [General Ethernet].
*
When using the driver, be sure to refer to the Device Connection Manual PDF (Shown above). Also, for general information regarding Device connection and documentation conventions please refer to "Device/PLC Connection Manual".
Update History:
[Ver. 1.11.02] (Nov. 12, 2009)
The following issues were corrected:
The source port number destination cannot be switched between the Memory table and U/I destinations in some cases.
CPU utilization may become 100% when the driver is used with WinGP.
In the offline mode, different numbers can be set as the local Port No. in the Communication Settings and the Control Area 1 settings.
A number smaller than 1024 can be set as the local port number in the offline mode of Middle-size display units.
GP-Pro EX may look as if it were locked up when an out-of-range value is input in the Control Area Setting dialog.
An error occurs when a command is sent with the Attribute Bit2, Bit3, and Bit4 ON.
Opening the connection may lead to an error when the port number auto-allocation setting is enabled.
A warning dialog may be displayed twice when an out-of-range value is input in the Control Area Setting dialog.
[Ver. 1.11.01] (Jun. 8, 2009)
The following settings were added:
Up to 8 port numbers on a GP unit can be selected.
Support for Device Monitor.
[Ver. 1.10.01] (May. 12, 2008)
The following issues were corrected:
The command is not transmitted.
When DPI setting of Windows OS is 120 DPI, Contorl Area Settings dialog is not normally displayed.
When write to system area, display takes time till the value reflects in screen.
Last Updated : Nov. 12, 2009
Posted :May. 12, 2008
