EZ Numpad
General Specifications
| Model | PFXZCCEUKB1 |
|---|---|
| Supported Standards and Regulations |       |
| Supported Software | GP-Pro EX Ver. 3.6 or later |
Electrical Specifications
| Power Supply | ||
|---|---|---|
| Rated Input Voltage | 5 Vdc (Powered from USB bus) | |
| Input Voltage Limits | 4.75 to 5.25 Vdc | |
| Power Consumption | 0.75 W or less | |
Environmental Specifications
| Physical Environment | |
|---|---|
| Surrounding Air Operating Temperature | 0 to 55 ℃ (32 to 131 ℉) |
| Storage Temperature | -20 to 60 ℃ (-4 to 140 ℉) |
| Surrounding Air and Storage Humidity | 10 to 90% RH (Non-condensing, wet bulb temperature 39 ℃ [102.2 ℉] or less) |
| Dust | 0.1 mg/m3 (10-7 oz/ft3) or less (nonconductive levels) |
| Pollution Degree | For use in Pollution Degree 2 environment |
| Corrosive Gasses | Free of corrosive gas |
| Operating Altitude | 2,000m [6,561 ft] or lower |
| Mechanical Environment | |
| Vibration Resistance | IEC/EN 61131-2 compliant 5 to 9 Hz Single amplitude 3.5 mm (0.14 in.) 9 to 150 Hz Fixed acceleration: 9.8 m/s2 X, Y, Z directions for 10 cycles (100 min.) |
| Concussion Resistance | IEC/EN 61131-2 compliant (147 m/s2, X, Y, Z directions for 3 times) |
| Electrical Environment | |
| Electrostatic Fast Transient Burst | IEC61000-4-4 2 kV Power Port (Display Unit) 1 kV Signal Ports |
| Electrostatic Discharge Immunity | IEC61000-4-2 6 kV Contact Discharge 8 kV Air Discharge |
External Specifications
| Connector Type | Type miniB (socket), USB 2.0 Full Speed |
|---|---|
| External Dimensions | W97.6 x H80.0 x D31.5 mm (W3.84 x H3.15 x D1.24 in.) |
| Structure *1 | IP65 UL50E TYPE 4X (Indoor Use Only) (on the front panel when properly installed in an enclosure) |
| Weight | 150 g (0.33 lb) or less |
- The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the unit’s level of resistance is equivalent to the UL50E TYPE 4X, oils that should have no effect on the unit can possibly harm the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the panel for long periods of time. If the unit’s front face protection sheet peels off, these conditions can lead to the ingress of oil into the unit and separate protection measures are suggested.
Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel’s plastic cover. Therefore, prior to installing the unit, be sure to confirm the type of conditions that will be present in the unit’s operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, the periodical maintenance is essential.
Note:
- A gasket with scratches or dirt could have lost much of its water resistance. The periodical maintenance is essential (e.g. once a year, or as soon as scratches or dirt become visible) for water resistance equivalent to IP65.
Dimensions
mm (in.)
A. Num Key / Function Key
Dimensions with cable
mm (in.)
B. USB (Type miniB) Interface