1.5.16.1 For Those Using the SP5000 Series

The following are the features and precautions for the SP5000 series.

• Refer to the following for the Box Modules and Display Modules you can connect together.
  1.4.3 SP5000 Series

• NVRAM is used as a backup memory. Please regard all instances of "SRAM" in this document as "NVRAM".

• The features you can use on the Premium Display, Advanced Display, and eXtreme Display are different. If you are replacing the display module, check the differences in features first.
  1.5.16.2 SP5000 Series

• Open Box not only runs project files created with GP-Pro EX and communicates with the device/PLC, but also allows you to run user-created applications built using API functions. For more details, please refer to the following.
  39.1 Overview

• Set the IP addresses for LAN1 and LAN2 with different network segments. If you set an IP address with the same network segment in the display unit, the communication may not work properly.

• Even if the display unit has multiple LAN ports, it cannot offer routing or bridge functionality.

• If a forced transfer dialog box displays when using a box module other than the Open Box, use the LAN1 port (Ethernet1) for Ethernet forced transfer. If you use the LAN2 port (Ethernet2), the Transfer Tool cannot recognize the box module.

• When changing from a non-SP5000 series model to a SP5000 series model, or when changing between SP5000 series models, see the following.
  5.6.1 Restrictions on Changing Models

• If you display the system menu or Brightness/Contrast Control Bar in offline mode, updates to time display or other displays will be suspended temporarily.

• SP5000 series project files can only be transferred to the same box module type.

* 1 You cannot transfer project files when SP-5700WCD or SP-5800WCD is set as the display module.

As the display module set in the project file is different from the one set in the location where the file is transferred to, the display may be cut off, enlarged, reduced, or otherwise display incorrectly.

• As the eXtreme Display does not have a status LED, for example you cannot use the breathing LED to check the standby mode status when standby mode is set to [Screen OFF].

About the System Card

In the SP5000 series (excluding Standard Box), the system card contains information required to operate the display unit, such as system settings and project files for the display unit. We recommend backing up the system card periodically. If a box module is corrupted, you can just insert the system card you backed up in another box module of the same model, making recovery quick.

• For backing up the system card, refer to our support site (http://www.pro-face.com/trans/en/manual/1001.html).

• We recommend that you set a password to prevent any unauthorized use of the system card data in other box modules.
  23.10.1.1 Password Settings

• When replacing the system card, turn off the display unit and remove the box module from the display module. Check the Hardware Manual for how to replace the system card and for optional equipment required for maintenance.

• eXtreme Box, eXtreme Display: SP-5000X Series Hardware Manual

• Other models: SP-5000 Series Hardware Manual

When using with DC Power Supply Adapter for Box Module attached and without a Display Module

When DC Power Supply Adapter for Box Module is attached, you can use a box module (except for the eXtreme Box) even without a Display Module.
For usage, refer to the "DC Power Supply Adapter for Box Module Installation Guide" or "SP5000 Series Hardware Manual".
You can download the manual from our support site (http://www.pro-face.com/trans/en/manual/1001.html).

• When transferring a project file or using offline mode, make sure a display^*1 with the same resolution as the [Screen Size] specified in the project is connected. It may not be possible to determine whether setup was completed properly.
  
  *1 Power Box/Standard Box: Display Module. Open Box: Display Module, flat panel display or other commercially available display

  

  • Refer to the following for supported display modules.
    1.4.3 SP5000 Series

• In the System Settings [Display Unit] - [Remote Viewer], select [Pro-face Remote HMI] - [Enable]. If an error occurs, you can check them with the Pro-face Remote HMI.

• When using the feature that stores the status in the internal device or the device/PLC address, design so that the external device can detect any display unit errors, as needed, by monitoring address values or using I/O.

• When using the Open Box, you cannot use the DC Power Supply Adapter's SD card eject switch. For steps on removing the SD card, refer to the "DC Power Supply Adapter for Box Module Installation Guide".

• When using the Power Box or Standard Box, you cannot use the LAN port on the DC Power Supply Adapter.

Front USB port

The front USB port on the SP5000 Series Premium Display is disabled at the time of purchase.
To use the front USB port, enable the setting as follows.

• When using Standard Box or Power Box

Select [Display Unit] - [Operation Settings] - [Memory Card Settings] and enable the [USB Front Port] setting.
5.4.4.4 Display Unit [Mode] - Memory Card Settings

Use the front USB port after transferring a project with the settings enabled.

• When using Open Box

Enable the front USB port setting in the launcher.
Refer to the "SP5000 Series Open Box Reference Manual" for information about the launcher. You can download the manual from our support site (http://www.pro-face.com/trans/en/manual/1001.html).