31.4.4.1 Error Code - FLEX NETWORK

001

Not supported unit.

This model is incorrect. (model of unsupported unit.)

The project file may not have been sent correctly. Transfer the project file again.

002

Setting value error

The data type of the symbol variable assigned to the FLEX NETWORK unit is illegal. The FLEX NETWORK unit setting value is illegal.

003

Device out-of-range error

The address of the symbol variable assigned to the FLEX NETWORK unit is out of range.

004

Duplicate terminal settings

The number of FLEX NETWORK unit terminals exceeds the limit.

005

Terminal setting order error

The I/O terminal numbers are not set up in ascending order.

006

Terminal registry short

Not a reasonable number of I/O terminals.

007

Units config overlapped.

FLEX NETWORK unit station number is duplicated and set.

008

Units count over limit.

The maximum number of connected FLEX NETWORK units (63 units) is exceeded. You have exceeded the maximum station number value (S-No.63). Station number of the FLEX NETWORK unit that occupies more than one node has exceeded the maximum (S-No.63).

009

Repeat driver setting

The driver is registered twice.

010

Unmatched In/Out terminal.

The input/output settings of the FLEX NETWORK unit are not correct.

011

Unmatched bit/word term.

The variable type specified in the FLEX NETWORK unit is incorrect.

012

Setting level value error

There is a problem with the I/O driver.

013

Data obtaining address error

I/O driver information is incorrect. Invalid controller information.

014

Driver/unit not registered

The I/O driver or FLEX NETWORK unit is not registered.

Error No.

Error Message

Cause

Solution

050

I/O board ID mismatch

Wrong I/O board is inserted.

The display type might not be correct. Check the Display Unit type and transfer the project file again.

051

Memory init. error

An error may have occurred during memory initialization.

The project file may not have been sent correctly. Transfer the project file again. If this does not resolve the problem, the hardware itself may be broken. Please contact customer support.

Error Code

Error Message

Description

Solution

100

Unit communication error.

A communication error has occurred between the main unit and the FLEX NETWORK unit. Possible causes are that the communication cable is disconnected; the FLEX NETWORK unit is not connected; or an incorrect unit model is set in the project file.

The station number or communication speed set in the editor may differ from that set in the unit. If this error continues, check the following.

• Communication cable disconnection

• Unit power supply

• Termination resistor setting of unit

101

4ch analog setting error.

Communication with the 4 CH analog unit has failed.

Check the following items:

• Communication cable disconnection

• Unit power supply

• Termination resistor setting of unit

• Editor settings and model of the connected unit

102

2ch analog setting error.

Communication with the 2 CH analog unit has failed.

103

Analog unit's wire broken.

The 4 to 20mA-ranging input signal of the 4 CH or 2 CH analog unit is cut off. This error code continues to display until the controller is reset.

Check if the input signal is disconnected.

104

Counter unit error.

An error has occurred in the high-speed counter unit.

For details, find the associated unit's error code in the following manual.

FLEX NETWORK High Speed Counter Unit User Manual

105

Counter initial error.

Initializing the high-speed counter unit has failed.

Check the following items:

• Communication cable disconnection

• Unit power supply

• Termination resistor setting of unit

• Editor settings and model of the connected unit

106

Counter communication error.

A communication error with the high-speed counter unit has occurred.
Possible causes of this error are that the communication cable is disconnected; the high-speed counter unit is not connected; or an incorrect unit model is set in the project file.

107

Positioning Unit error.

An error has occurred in the positioning unit.

For details, find the associated unit's error code in the following manual.

FLEX NETWORK Single-Axis Positioning Unit User Manual

108

Comm position error.

A communication error with the positioning unit has occurred.
Possible causes of this error are that the communication cable is disconnected; the positioning unit is not connected; or an incorrect unit model is set in the project file.

Check the following items:

• Communication cable disconnection

• Unit power supply

• Termination resistor setting of unit

• Editor settings and model of the connected unit

109

2ch analog comm error.

A communication error with the 2 CH analog unit has occurred.
Possible causes of this error are that the communication cable is disconnected; the 2ch. analog unit is not connected; or an incorrect unit model is set in the project file.

Solution

200

Integer type data read error.

Integer-type Terminal data of the FLEX NETWORK unit could not be read.

The project file may not have been sent correctly. Transfer the project file again.

201

Bit type data read error

Bit-type Terminal data could not be read.

202

Integer type data write error

Integer-type Terminal data could not be written.

203

Bit type data write error

Bit-type terminal data could not be written.