Otasuke Pro! Technical Resource > Otasuke FAQ's Book

		GP-2300T	GP-3300T
Display Type		TFT color LCD	TFT color LCD
Brightness Control		256 Colors	65536 Colors
Display Resolution		320×240 pixels	320×240 pixels
Panel Cutout (mm)		156(W)×123.5(H)	156(W)×123.5(H)
Dimensions (mm)		171(W)×138(H)×60(D)	167.5(W)×135(H)×59.5(D)
Touch Panel Type		Matrix Type	Resistive Film (Analog) Type
Serial I/F	COM1	D-Sub25P(female) RS-232C/422	D-Sub9P(male) RS-232C/485 (422)
Serial I/F	COM2	D-Sub9P(male) RS-232C	D-Sub9P(female) RS-485 (422)
Memory	Application	2MB	6MB
Memory	SRAM	256KB	320KB
Ethernet I/F		10BASE-T	10BASE-T/ 100BASE-TX
CF card I/F		○	○
printer I/F		Centronics (parallel)	USB

*Please Read

1 )Touch Panel Specifications

It is "Analog form " in GP3300T.
In "Analog form", It doesn't recognized as the touch input when you touch two points at the same time. Therefore, please do not push two points at the same time.
If you used two points input with GP-2300T, we will encourage to change to one point input in the application by using switch delay function.

2)The COM1 and COM2 of Serial Interface

In GP-3300T, the COM1 is the D-Sub 9 pins male connector, the COM2 is the D-Sub 9 pins female.
In GP-2300T, the COM1 was the D-Sub 25 pins female connector, the COM2 was the D-Sub 9 pins male connector. The pin array and the shape of male/female connector is different to GP-3300T.
Therefore, when you connected with PLC cable, you have to be careful to connect it. Please refer to here for the interchangeability of the PLC connection.

3)Printer connection

GP-3300T does not equip the centronics (parallel) interface for the printer.
When you used the printer that was connected by the centronics interface with GP-2300T, you need to have the conversion machine that converts USB of GP-3300T into centronics.

4)Bar-code reader connection

GP-3300T does not equip with the tool port. Therefore, the bar-cord reader that connected from GP-2300T tool port cannot be used. However, the bar-code reader can be connected from the USB interface or the serial interface in GP-3300T.

5)Transfer Screen Date

GP-3300T uses USB or Ethernet to transmit the screen data. The cable must use the special transfer cable (The model: CA3-USBCB-01) for the GP3000 series. Please note that the commercial USB cable cannot be used.
Although the transfer screen data used the tool port in GP-2300T, the transfer cable (*1) for GP2000 series is different from GP-3300T.
The Ethernet transfer can be used as well as before.

*1 GP-2300T Transfer cable model: GPW-CB02,GPW-CB03,GP430-CU02-M, etc..

6)Power Supply

In GP-3300T, there are two kinds power supply, the AC type and the DC type.
The AC type's Terminal Block is the same as GP-2300T. The DC type's power supply of GP-3300T is a screw lock terminal block. Therefore, the power cable changes when replacing it from GP-2300T.

7)Expansion Unit

GP-3300series doesn't correspond to various expansion units.(*2) .

*2 We prepare Profi-bus unit (model:CA5-PFSALL/EX-01) for GP3300 series. The other field bus unit is under developing now.

↑Back to page top

← Return to the previous page

FAQ for use | Protection of Personal Information | Trademark Acknowledgments | About Intellectual Property Rights | Terms of Use