T.7.4 When the LT series / STC6000 series is used

This error appears when using the standard driver, STD driver (STD4S driver), or an EXM driver / TM3 driver.

Any of the following error messages appears depending on the result of the I/O monitoring of the module connected to the STD driver.

Error Code	Error Message	Cause and Solution
RGEE001	Invalid module type	The specified module type is not supported. The project file may not have been sent correctly. Transfer the project file again.
RGEE002	Setting value error	The type of the variable assigned to the terminal is invalid, or the terminal setting is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEE003	Device out-of-range error	The variable address assigned to the terminal is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEE004	Too many term. setting	The number of terminals is invalid. (The number of terminals is excessive.) The project file may not have been sent correctly. Transfer the project file again.
RGEE005	Terminal setting order error	The terminal numbers are not arranged in ascending order. The project file may not have been sent correctly. Transfer the project file again.
RGEE006	Insufficient number of terminal registration	The number of terminals is invalid (insufficient number of terminals). The project file may not have been sent correctly. Transfer the project file again.
RGEE007	Module settings duplicated	Module registration is duplicated. The project file may not have been sent correctly. Transfer the project file again.
RGEE008	Excess module settings	The number of modules is invalid (excess number of terminals). The project file may not have been sent correctly. Transfer the project file again.
RGEE009	Driver settings duplicated	Driver registration is duplicated. The project file may not have been sent correctly. Transfer the project file again.
RGEE010	Inconsistent I/O settings	The terminal setting is invalid (inconsistent I/O setting of the module). The project file may not have been sent correctly. Transfer the project file again.
RGEE011	Inconsistent bit/integer type	The terminal setting is invalid (inconsistent variable type setting of the module). The project file may not have been sent correctly. Transfer the project file again.
RGEE012	Setting level value error	The driver is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEE013	Data obtaining address error	The driver information or controller information is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEE014	Invalid driver ID	Because an error occurred during driver/module registration, the driver/module has not been registered. The project file may not have been sent correctly. Transfer the project file again.
RGEE015	Module setting order error	The module numbers are not arranged in ascending order. The project file may not have been sent correctly. Transfer the project file again.
RGEE016	File version mismatch	The driver file version does not match. The project file may not have been sent correctly. Transfer the project file again.
RGEE050	I/O board ID mismatch	Wrong I/O board is inserted. The display type might not be correct. Check the Display Unit type and transfer the project file again.
RGEE051	Unsupported model	The model does not support this driver. The display type might not be correct. Check the Display Unit type and transfer the project file again.
RGEE052	I/O init. error	The system failed during I/O board initialization. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE053	I/O ROM error	An error occurred with the I/O board system ROM. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE054	I/O RAM error	An error occurred with the I/O board system RAM. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE055	I/O microprocessor err	An error occurred with the I/O board microprocessor. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE056	I/O IF RAM error	An error occurred with the I/O board system I/F RAM. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE057	I/O E2PROM error	An error occurred with the I/O board system E2PROM. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE100	I/O board error	The I/O board is not responding. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE101	Special I/O error	An error occurred with the special I/O parameter setting. The parameter setting is invalid. Correct the parameter setting, and issue a parameter change request.
RGEE102	Acc/Dec table error	An error occurred with the special I/O parameter setting. The parameter setting is invalid. Correct the parameter setting, and issue a speed-up/down table preparation request.
RGEE103	Init. parameter error	An error occurred with the special I/O parameter setting for initial processing. The parameter setting is invalid. Correct the parameter setting, and issue a parameter change request.
RGEE108	Analog data range error	Upper limit and lower limit setting values of the analogue module are faulty. The project file may not have been sent correctly. Transfer the project file again.
RGEE127	Analog output error	Analogue output request flag write is not completed. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE128	Output data error	The output data is out of the setting range, or the data output is stopped. Output data within the setting range. This error code continues appearing until the controller is reset.
RGEE129	Analog power error	An external power supply is not connected to the analog module. Connect a power supply to the analog module. This error code continues to appear until the controller is reset.
RGEE130	Input data error	The input data is out of the setting range, or the data input is stopped. Input data within the setting range. This error code continues to appear until the controller is reset.
RGEE131	Pulse output error	There is a problem with the pulse output. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEE132	Analog input wire error	The wiring in the analog input cable may be damaged. Connect an undamaged analog input cable.
RGEE133	Temperature wire error	The wiring in the temperature input cable may be damaged. Connect an undamaged temperature input cable.
RGEE134	Temperature range error	The settings for the temperature input's measurement object are incorrect, or the measurement object failed. Connect a measurement object that is working correctly.
RGEE200	Word read error	The system failed while reading integer-type terminal data. The project file may not have been sent correctly. Transfer the project file again.
RGEE201	Bit read error	The system failed while reading bit-type terminal data. The project file may not have been sent correctly. Transfer the project file again.
RGEE202	Word write error	The system failed while writing integer-type terminal data. The project file may not have been sent correctly. Transfer the project file again.
RGEE203	Bit write error	The system failed while writing bit-type terminal data. The project file may not have been sent correctly. Transfer the project file again.

Any of the following error messages appears depending on the result of the I/O monitoring of the module connected to the EXM driver / TM3 driver.

Error Code	Error Message	Cause and Solution
RGEF001	Invalid model	The specified module type is not supported. The project file may not have been sent correctly. Transfer the project file again.
RGEF002	Setting value error	The type of the variable assigned to the terminal is invalid, or the terminal setting is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEF003	Device out-of-range error	The variable address assigned to the terminal is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEF004	Too many terminals setting	The number of terminals is invalid. (The number of terminals is excessive.) The project file may not have been sent correctly. Transfer the project file again.
RGEF005	Terminal setting order error	The terminal numbers are not arranged in ascending order. The project file may not have been sent correctly. Transfer the project file again.
RGEF006	Insufficient number of terminal registration	The number of terminals is invalid (insufficient number of terminals). The project file may not have been sent correctly. Transfer the project file again.
RGEF007	Module settings duplicated	Module registration is duplicated. The project file may not have been sent correctly. Transfer the project file again.
RGEF008	Excess module settings	The number of modules is invalid (excess number of terminals). The project file may not have been sent correctly. Transfer the project file again.
RGEF009	Driver settings duplicated	Driver registration is duplicated. The project file may not have been sent correctly. Transfer the project file again.
RGEF010	Inconsistent I/O settings	The terminal setting is invalid (inconsistent I/O setting of the module). The project file may not have been sent correctly. Transfer the project file again.
RGEF011	Inconsistent bit/integer type	The terminal setting is invalid (inconsistent variable type setting of the module). The project file may not have been sent correctly. Transfer the project file again.
RGEF012	Setting level value error	The driver is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEF013	Data obtaining address error	The driver information or controller information is invalid. The project file may not have been sent correctly. Transfer the project file again.
RGEF014	Invalid driver ID	Because an error occurred during driver/module registration, the driver/module has not been registered. The project file may not have been sent correctly. Transfer the project file again.
RGEF015	Module setting order error	The module numbers are not arranged in ascending order. The project file may not have been sent correctly. Transfer the project file again.
RGEF016	File version mismatch	The driver file version does not match. The project file may not have been sent correctly. Transfer the project file again.
RGEF050	I/O board ID mismatch	Wrong I/O board is inserted. The display type might not be correct. Check the Display Unit type and transfer the project file again.
RGEF051	Unsupported model	The model does not support this driver. The display type might not be correct. Check the Display Unit type and transfer the project file again.
RGEF052	I/O board init. error	The system failed during I/O board initialization. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEF100	Module init. error	The module may not be properly connected. Reconnect the module properly and turn the power on again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEF101	Module init. resp err
RGEF102	Module init. send err
RGEF103	Module init. rcv. err
RGEF104	Module init. end err
RGEF105	Module connections err	The connected I/O board does not match. The display model may be different. Check the display model, and transfer the project file again.
RGEF106	Unsupported module	The connected module is not supported. Remove the unsupported module and then turn ON electric power again.
RGEF107	Mode setting error	Mode setting value is faulty. The project file may not have been sent correctly. Transfer the project file again.
RGEF108	Analog data range error	There a problem with the analog module's upper and lower limit values. The project file may not have been sent correctly. Transfer the project file again.
RGEF109	Module settings error	The module does not operate due to the data mismatch between the connected module and the set data. The setup information in the project and the connected module are different. Connect the specified module, and turn ON the power switch again.
RGEF120	Module validation err	There is a mismatch between a connected module and the set data, however the module is partially running. The setup information in the project and the connected module are different. Connect the specified module, and turn ON the power switch again.
RGEF121	Module response error	The module may not be properly connected. Reconnect the module properly and turn the power on again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEF122	Module send error
RGEF123	Module receive error
RGEF124	Module comm. setting	Difficulties in transmission data. The module may not be properly connected. Reconnect the module properly and turn the power on again. The display unit may be faulty. Please contact customer support.
RGEF125	Module ACK error	The module may not be properly connected. Reconnect the module properly and turn the power on again. The display unit may be faulty. Please contact customer support.
RGEF126	Module comm. error
RGEF127	Analog output error	Analog output request flag did not complete writing. The project file may not have been sent correctly. Transfer the project file again. If this error persists, the GP unit may be faulty. Please contact customer support.
RGEF128	Output data error	Output data is outside the settings range, or has stopped. Output data that is within the settings range. This error code continues to appear until the controller is reset.
RGEF129	Analog power error	An external power supply is not connected to the analog module. Connect a power supply to the analog module. This error code continues to appear until the controller is reset.
RGEF130	Input data error	Input data is outside the settings range, or has stopped. Input data that is within the settings range. Or the analogue input cable might be damaged. Connect an undamaged analogue input cable. This error code continues to appear until the controller is reset.
RGEF200	Word read error	The system failed while reading integer-type terminal data. The project file may not have been sent correctly. Transfer the project file again.
RGEF201	Bit read error	The system failed while reading bit-type terminal data. The project file may not have been sent correctly. Transfer the project file again.
RGEF202	Word write error	The system failed while writing integer-type terminal data. The project file may not have been sent correctly. Transfer the project file again.
RGEF203	Bit write error	The system failed while writing bit-type terminal data. The project file may not have been sent correctly. Transfer the project file again.

Error codes and messages stored in #L_IOStatus		Values reflected in user-defined I/O variable
RGEE130	Input data error	Dec: 65535 / HEX: FFFF
RGEE132	Analog input wire error	Dec: 65534 / HEX: FFFE
RGEE133	Temperature wire error	Dec: 65534 / HEX: FFFE
RGEE134	Temperature range error	Dec: 65535 / HEX: FFFF