Products
Download
Contact us
Back to Top
 Software Update Module / Add-on Software
 > Factory Gateway Update  >Factory Gateway Add-on Software
Pro-Server with Pro-Studio (Ver. 4.02)

Please acknowledge the following terms of use before you use our download service. Download of any file signifies your agreement to the terms of use.

Terms of Use
  1. Schneider Electric Japan Holdings Ltd. ("SEJH") shall retain all intellectual property rights to the files that SEJH provides for this service.
  2. Who, uses or plans to use SEJH's products, may download and use any file.
  3. Reproduction, disclosure, re-publication, assignment, lease, decompilation, modification, falsification or reuse of any file that SEJH provides for this service shall be prohibited.
    However, for manuals, samples, BMP images and CAD files, you may reprint, duplicate, quote a part of the content or the whole on your company's specification sheets, or instruction manuals for built-in products. Also you may change the layout of the content.
  4. This download service is provided through the Internet. Please acknowledge that SEJH provides no guarantee of the condition at the time of provision, the availability of access and the condition of use concerning this service before you use this service.
  5. Please use this service at your own risk.
  6. If any additional conditions such as service usage conditions are attached to the downloaded files, please comply with such conditions as well.
Notices:
  1. Files are subject to deletion, or modification of the contents or specifications without notice.
  2. Please confirm that the downloading file size completely accords with the download file size shown.
  3. If the file sizes do not match, delete the file without decompressing and then download the same file once again.
 Download
The following Add-on software module is that even if GP-PRO/PB III is not installed, to allow you to set up Factory Gateway units to communicate with a PLC or a temperature controller using only Pro-Server (Ver. 4.02).

- Factory Gateway Usage Notes
*Pro-Server with Pro-Studio is required when operating the Factory Gateway unit.
 
File Name Pro-ServerV402.exe
File Size 11,385KB
File Description Pro-Server with Pro-Studio Add-on Software (Ver. 4.02) for Factory Gateway units.
Applicable Versions Pro-Server with Pro-Studio Ver. 4.0 or 4.01
Description
1. Updates the Pro-Server with Pro-Studio software to Ver. 4.02, and, even if GP-PRO/PB III is not installed, allows Factory Gateway units to be set up to communicate with a connected controller using only Pro-Server (Ver. 4.02).
(Factory Gateway Configuration Tool)
   
2. Corrects the following errors.

- When the PC's monitor resolution is set to VGA [640 x 480], occasionally the Status Monitor cannot be started up from Pro-Studio.
- After operating for approximately 24 hours, Pro-Server's Auto Polling function (cache) stops.

*This Update module also includes the Ver. 4.01 Update module.

Please refer to the following PDF manuals for Factory Gateway unit operation.
- Factory Gateway User Manual

Notes about Installation
Do not uninstall your currently installed GP-PRO/PB III or Pro-Server with Pro-Studio software. This update module overwrites only the program codes that needs to be modified. It does not install a completely new version of the program.
Prior to installing an Update module, be sure to quit all applications and resident programs (virus detection, etc.).

Notes about Pro-Server with Pro-Studio Update Module
1. Prior to installing the Pro-Server Update modules, be sure to install Pro-Server Ver. 4.0. The Update modules cannot be installed if Pro-Server Ver. 4.0 is not already installed.
2. To use Factory Gateway units, driver files for the type of device/PLC your are using are needed.
Please follow the driver file's installation instructions to install this software.

During the Pro-Server Update module installation, the installer will ask, “Is GP-PRO/PB III for Windows installed in your computer?” After reading the following, choose [Yes] or [No].

When GP-PRO/PB III for Windows Ver. 6.0 or later is installed

--> choose [Yes]
When GP-PRO/PB III for Windows is installed using the "standard installation", all the necessary driver files have also been installed. As a result, these Update modules will skip the driver file installation.
When you are asked to designate the folder location where GP-PRO/PB III for Windows is installed, select that folder. The Factory Gateway Configuration Tool will then use the driver files in that folder.

Caution: If, by accident, the wrong folder is designated for GP-PRO/PB III for Windows, Update module installation will not proceed until the folder where GP-PRO/PB III for Windows is installed is correctly designated.
When GP-PRO/PB III for Windows is installed using the "standard installation", the destination folder location is [C:\Program files\pro-face\ProPBWin\].

When GP-PRO/PB III for Windows Ver. 6.0 or later is installed

--> choose [No]
Since no driver files have been installed yet on the PC, these Update modules will install driver files in Pro-Server's installation folder.
The Factory Gateway Configuration Tool will then use the driver files in that folder.

Important: When GP-PRO/PB III for Windows is installed using the "custom installation", and the driver files required for Factory Gateway operation are not installed, choose [No].
If, prior to making a [Yes] or [No] selection you immediately install the protocol files required for GP-PRO/PB III for Windows, you can choose [Yes] here.

3. How to use the Factory Gateway Configuration Tool, please refer to the following PDF manuals.(After Update module installation is finished, the Factory Gateway Configuration Tool is installed in the Pro-Server folder.)

- Factory Gateway Configuration Tool Operation Manual

Last Updated : April.8.2002
| Return to Top | | Back | HOME |
FAQ for use | Protection of Personal Information | Trademark Acknowledgments | About Intellectual Property Rights | Terms of Use
Copyright (C) 2005- Schneider Electric Japan Holdings Ltd. All Rights Reserved.